This error might occur because the reference has been deleted. 1557 LabVIEW tried to access duplicate references at the same time. 1558 There is a type mismatch between the wire type This could be caused by an invalid sound driver. 4801 Invalid sound task refnum. Attempted to read from or write to a file of a type incompatible with the operation. When a Boolean control is configured with a latching mechanical action, the Value property always returns an error. http://arxlabsolutions.com/error-code/nrg-error-codes.php
Refer to the KnowledgeBase for more information about correcting errors in LabVIEW. The specified file is not a valid palette file (.mnu). A VI item in the palette data array is not supported in this version of LabVIEW. If you receive this error while using the Sound Output Configure VI, refer to the KnowledgeBase at ni.com for more information. 4804 Cannot write in file playback. http://zone.ni.com/reference/en-XX/help/371361J-01/lverror/misc_lv_error_codes/
Possible Cause: Often EDVR errors are caused when you misspell the interface name of your board or the device name of your instrument. Check that the parameters entered are within the supported range for the hardware and drivers. For example, the network connection is down or a network cable is unplugged. 7 File not found. The project has a locked untitled dependency.
To correct this error, load an instance of the polymorphic VI rather than the polymorphic VI itself. 1554 The current LabVIEW target cannot load control VIs. 1556 The reference is invalid. Make sure you installed Microsoft Word correctly. 1624 You can only generate web page or plain text reports on OS X and Linux. 1627 The control index at position %d is VISA-specified defaults will be used. 1073676413 Session opened successfully, but the device at the specified address is not responding. 1073676414 The path from trigSrc to trigDest is already mapped. 1073676416 Wait Labview Error 200279 If you only need read access, you can use the Open/Create/Replace File function with the access input set to Read-only.
This error also can occur if you attempt to obtain a VI's image while the VI is being modified programmatically. You must have DIAdem 9.1 Service Pack 2 or later installed to use the DIAdem Report Express VI. −2580 The Write to Measurement File Express VI cannot append new data to For example, hexadecimal notation is not a valid format for floating point numbers. 1434 The precision is greater than the maximum allowed value for this format. 1436 Numeric precision cannot be An input task might stop running if the input buffer overflows.
NoteYou must manually create an errors folder in the labview\user.lib directory to organize your error code files. Labview Visa Error Codes All rights reserved.| Cart|Help You are here:NI Home > Support > Manuals > LabVIEW 2012 Help VISA Error Codes »Table of Contents LabVIEW 2012 Help Edition Date: June 2012 The exception might have corrupted the LabVIEW memory. This error can occur when you write a frequency domain waveform to a file with Segment Headers set to One header only.
The frequency for a data point is then calculated as f0+N*df. Source To correct this error, install the latest version of DirectX from http://www.microsoft.com/downloads. 4810 Cannot recognize sound format. Daqmx Error Codes To correct this error, ensure that the names you use for drag data are unique in each element of the data array for the method or event. 1385 Cannot start a Labview Visa Error -1073807339 To correct this error, verify that the file is not in use by another application and that file permissions are set correctly.
YourFeedback! http://arxlabsolutions.com/error-code/nordictrack-error-codes.php The floating point data was outside of the range [-1.0, 1.0]. Verify the values you wired to the Call Library Function Node. 1098 Cannot disconnect type definitions or polymorphic VIs if the block diagram is not available. 1100 No object of that Enter the error code number in the Code field or, if the error code number is in hexadecimal format, in the Hex Code field. Labview Custom Error Codes
You cannot assign the same numeric value to two or more strings in a ring control, and you cannot assign the same string value to two or more strings in a Most likely the VI is broken or one of its subVIs cannot be located. To correct this error and inline the subVI, remove the implicit Property Node or Invoke Node. 1488 The migration file cannot load because it is no longer supported. 1489 The migration Source Use a VI with the custom control on its front panel instead. 4800 Selected Device is Invalid The currently selected device index is invalid.
Lengthen the timeout period for I/O operations using the ibtmo command. Labview Error 50103 Poor|Excellent Yes No Document Quality? An array must have 1 or more dimensions. 1176 Invalid waveform dimension in Call Library Function Node configuration.
To resolve this error, give the file a path that does not already contain a LabVIEW file in any open application instance. 1358 The splitter bar cannot be moved to this If you do not have the right amount of data to align to a sector size, you must pad the data with filler data and delete the filler data before LabVIEW One of the specified arguments is invalid. −1967345147 Entry not found. Labview Fpga Error Code Try freeing up disk space or saving to a different disk or drive.
Please tell us why. One of the specified arguments is invalid. −1967345147 Entry not found. The correct format should begin with the class type followed by the path to the object using the long names. have a peek here Legacy or Third-Party Drivers If you are using a driver that was released before LabVIEW 6.1, the driver installed a version of error.llb that contains all the driver error codes.
A timing source such as IEEE-1588 or GPS modified the global time value on the controller. This error also can occur if you attempt to open a reference to a VI that is running or reserved for running. For example, hexadecimal notation is not a valid format for floating point numbers. 1434 The precision is greater than the maximum allowed value for this format. 1436 Numeric precision cannot be You cannot use notifiers for communication between LabVIEW application instances. 1493 The save operation failed because multiple files of the same name cannot be saved into a single LLB.
By default, your GPIB board will be the System Controller, but this is not the same as being the Controller-In-Charge. A specified refnum was not valid. −1967345151 Invalid property code. This error occurs when you use an index value that is out of range to access a frame in a Case, Stacked Sequence, or Event structure. 1313 You cannot use this Paths to VIs and palette files (.mnu) must be valid. −4402 The palette view format is invalid.
This is caused by trying to allocate a buffer that is too large for memory. When you obtain a reference to a queue or notifier, you can specify which data type this mechanism stores. Any error noted below that has an associated quality (see notes under Other Representations) was actually returned by the Shared Variable Engine and passed through the error returned by ni_tagger_lv_Read or Both the 0x80 and 0x100 option flags conflict with the 0x08 option flag.
Right-click the container border and select Replace or drag new subtype. 1096 The Open VI Reference function cannot prepare a non-reentrant VI for reentrant run.